by Admin

Condensate Drain – Jorc

Fluid Drain

EZ-1

Timer controlled condensate drain

Product Features
The EZ-1 is designed to remove condensate from compressors, compressed air dryers and receivers up to any size, type or manufacturer.

The EZ-1 offers true installation simplicity at the lowest possible cost. The EZ-1 is a mass produced product available in various value connection sizes and timer color options.

Commercial Benefits
  • Does not air-lock during operation
  • Compressed air systems up to any size
  • Suitable for all systems up to any size
  • TEST (micro-switch) feature
Technical Advantages
  • Simple to install
  • Direct operated value – not diaphragm type
  • The direct acting value is serviceable
  • Viton seals
Product specifications
  • Maximum compressor system capacity                              Unlimited
  • Valve connection options                                                1/2″ , 3/8″ and 1/4″ BSP and NPT
  • Minimum system pressure                                               0 bar
  • Maximum system pressure                                              16 bar
  • Minimum medium temperature                                         2 C
  • Maximum medium temperature                                        50 C
  • Valve orifice                                                                   4.0 mm
  • Type of operating valve                                                   Direct acting
  • Valve seals                                                                     FPM (Viton)
  • Installation enclosure                                                      IP65/NEMA4
  • Voltage rang options                                                       24 to 230VAC/DC 50/60 Hz
  • Time cycle rang (On – Off)                                               0.5/10 seconds – 0.5/45 minutes
tec-44

TEC-44

Product Features The TEC-44 is a microprocessor operated ball valve, designed to remove condensate from deliquescent dryer, tank, vessels and refrigerated dryers.
The TEC-44 is designed to remove high viscosity effluents at pressure ratings up to 40 Bar. This condensate drain can not be blocked and is applied where all else fail.

Draining applications with a high level of contamination (rust, scale etc.) require the TEC-44. The TEC-44 is impossible to block due to its powerful ball valve rotation and large orifice.

Commercial Benefits
  • Does not air-lock during operation
  • compressed air systems up to any size
  • Powerful ball valve rotation (unblockable)
  • Suitable for all types of compressors
  • TEST (micro-switch) feature
Technical Advantages
  • Micro-processor controlled (high level of time cycle accuracy)
  • medium pressure up to 40 bar
  • Remote control – optional.
Product Dimension MM
  • Maximum compressor system capacity                              Unlimited
  • Valve connection options                                                   1/2″  BSP and NPT
  • Minimum system pressure                                                  0 bar
  • Maximum system pressure                                                 40 bar
  • Minimum medium temperature                                           2 C
  • Maximum medium temperature                                          50 C
  • Valve orifice                                                                     12 mm
  • Type of operating valve                                                     Motorised ball valve
  • Valve seals                                                                       FPM (Viton) and Teflon
  • Installation enclosure                                                         IP65/NEMA4
  • Voltage rang options                                                         24,115 or  230VAC/DC 50/60Hz
  • Time cycle rang (On – Off)                                                  7 seconds – 4 minutes/24 hours

POD

Pod Photo

Pneumatic operated zero air loss condensate drain
The POD is designed to remove upto 850 gallons of condensate from compressed air systems per hour. The POD uses compressed air as its power source to operate. It is therefore ideally suited to apply on applications where power is not available or desired. The operations is automatic and there is no compressed air lost during the condensate disch
rge cycle. The POD will save compressed air and electricity costsKey features
• Zero air losr during the condensate discharge
• No electricity required to operate the drain
• Condensate level indication, allowing visual inspection
• 150 Gallons of condensate discharge per hour maximum
• Medium pressure 45 to 230 psi
• Pneumatic operated valve – not diaphragm type
• Large (1/4″) valve orifice
• The diaphragm valve is servicing
• Test feature
• Suitable for all types of compressed air systemsSpecifications

 Product Name  POD
 Body Material  Zinc coated Aluminum
 Note  Failure to carry out routine draining can have catastrophic results.
Compressed air systems can become contaminated and production
schedules can get seriously disrupted- just because a simple duty
has been neglected.
 Condensate inlet
Connection Top and Bottom
 
 3/4 inch NPT
 Condensate Discharge
Outlet Connection
 1/2 inch NPT
 Min. – Max Pressure  2 PSI /230 PSI (Depending on model) psi
 Supply Valve Operating
Pressure
 2 PSI /230 PSI (Depending on model) psi
 Min. – Max. Medium
Temperature
 36 – 121 oF
 Valve Orifice  7mm lnch
 Max. Drainage Capacity  400 Gallons/Hour
 Valve Seal  FPM (Viton)
 Type of Valve Applied  Diaphram
 Max. Compressor Capacity  4500 cfm cfm

Video

Top